Welcome to the KeepItPrinting.com forums! The doctor is IN.

          
                                                            

Your business can be seen here! Prime spots available!
             

Please consider making a voluntary donation if you find these forums helpful. Thank you.
Home of the Kip Doctor!            REGISTER: In order to register for our forums please send an E mail to kiptech@earthlink.net stating what user                                                               name and password you would like. This is now required due to all the spambots that have been registering.
KeepItPrinting.com Forum Index KeepItPrinting.com
The "unofficial' and "unauthorized" KIP info site.


E-03 KIP 7000

 
Post new topic   Reply to topic    KeepItPrinting.com Forum Index -> Kip 7000 discussions
View previous topic :: View next topic  
caltech
resident


Joined: 24 Feb 2006
Posts: 225
Location: Northern California

 PostPosted: Tue Jun 27, 2017 5:45 pm    Post subject: E-03 KIP 7000 Reply with quote Back to top

Getting a constant E-03 on this old HDP 7000. Have replaced Main Motor, Main Motor Driver Board and Main DC Controller. Have checked all DC Power Supplies, all good. This one has me stumped. Anyone out there with some help for me, please?
 
View user's profile Send private message Visit poster's website
bigal
doctor


Joined: 17 Apr 2007
Posts: 288
Location: TEXAS

 PostPosted: Tue Jun 27, 2017 6:19 pm    Post subject: E03 Reply with quote Back to top

Have you checked to see if any binding (mechanical) in the main drive system?
Maybe bearings , belt slipping etc.
 
View user's profile Send private message Send e-mail Visit poster's website
caltech
resident


Joined: 24 Feb 2006
Posts: 225
Location: Northern California

 PostPosted: Tue Jun 27, 2017 6:28 pm    Post subject: Reply with quote Back to top

Yes, I'm running it now with the main motor belt removed so it is only the motor driving. If I mask the error I can run the motor fine in service mode. The motor runs fine then, unmask the error returns.
 
View user's profile Send private message Visit poster's website
bigal
doctor


Joined: 17 Apr 2007
Posts: 288
Location: TEXAS

 PostPosted: Tue Jun 27, 2017 6:33 pm    Post subject: E03 Reply with quote Back to top

In some of these printers the main gears would get worn badly.
I have the KIP Bulletin Tips K103IPS
It explains how to replace the plastic gears in drive system... Not sure this is causing your problem but...I can send it to you if needed
 
View user's profile Send private message Send e-mail Visit poster's website
CHILLIN
doctor


Joined: 05 Oct 2006
Posts: 900

 PostPosted: Fri Jun 30, 2017 11:06 am    Post subject: Reply with quote Back to top

Have you swapped out the Power supply or just tested it?
I just had a 7900 that was giving E-03 and E-07 errors intermittently 4-5 times during the day. Turns out the was something wrong with one the power supplies. I swapped both at the same time so I'm not sure which one was the culprit, but I haven't been back.
 
View user's profile Send private message
caltech
resident


Joined: 24 Feb 2006
Posts: 225
Location: Northern California

 PostPosted: Fri Jun 30, 2017 11:40 am    Post subject: Reply with quote Back to top

Unbelievable! It was the braded steel ground wire that grounds the main frame to the movable process unit. It was broken and just needed to be taped together.
 
View user's profile Send private message Visit poster's website
mark in vegas
doctor


Joined: 20 Oct 2010
Posts: 1705
Location: Las Vegas, NV

 PostPosted: Fri Jun 30, 2017 2:18 pm    Post subject: Reply with quote Back to top

Evil static
_________________
Regards,
Mark
RVN 68-69
“You can get more with a kind word and a gun than you can with a kind word.” Professor Erwin Corey
 
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    KeepItPrinting.com Forum Index -> Kip 7000 discussions All times are GMT - 3.5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum